UEC DSD 700 Especificaciones descargar pdf (Pagina 6)

6 OPERATING INSTRUCTIONS DSD 700

GETTING STARTED

NOTE: Unless absolutely necessary, do not change

installation, connections or decoder setup, or carry out

any retuning on a working system. If changes are

made, note all changed settings in the table on page

31.

Installation of the satellite dish and cabling to the

DSD

Installation procedures for satellite dishes and cabling to DSDs are

outside the scope of this manual. Please refer to the manuals

provided with your satellite dish and associated equipment if you

decide to do the installation yourself.

Installation Indemnity

1 For the decoder to operate, it is required to correctly install and

align a satellite dish and a Low Noise Block (LNB) converter.

2 Each and every INSTALLER acts as an independent contractor

and is not a servant, sub-contractor or agent of the

manufacturer. The manufacturer is, therefore, not liable for any

loss or damage of any nature whatsoever caused by the

conduct of the installer, including but not limited to:

a. Any direct, indirect or consequential damages of any

nature or any loss of profit or other special damages of

any nature which the USER may suffer as a result of any

breach by the INSTALLER of any of its obligations to the

USER.

b. Any loss or damage to any property of the user or

any third party, situated on the USER’s premises even if

loss or damage arises out of any part of the INSTALLER.

3 The manufacturer does not directly or indirectly warrant or

guarantee or make any representations whatsoever with

regard to any equipment, including, but not limited to any dish,

LNB, or cabling, used by the INSTALLER.

4 Subject to any express warrant or guarantee given by the

manufacturer, in writing, the manufacturer does not:

a. Give any warranty or guarantee or make any

representation whatever in respect of any work

carried out by the INSTALLER.

b. Accept any liability for any latent or other defect in any

work carried out by the INSTALLER.

Setting-up the System

1 Install and align satellite dish (installer).

2 Connect the decoder to the TV set (either SCART to SCART or

RF OUT on the decoder to RF IN on the TV). (See Optional

Decoder Connections.)

Switching on the Decoder at the Mains

When you switch on the decoder at the mains, it goes through a

power-up sequence, then attempts to find a signal at the specific

factory-set frequency. During this process, various indications are

displayed on the decoder display and TV, as shown in the following

sequence of drawings:

NOTE: If the TV is not tuned to the channel chosen to

view the satellite services, the sequence is still

the same, but the TV will not display the scanning

screen. To tune the TV to the decoder services,

tune the TV as per Tuning Your TV.

If your TV has been tuned to accept the decoder

services, but your smart card has not been inserted

into the decoder, an error message will appear on your

TV screen.

If your decoder was in standby mode at mains power

switch off, the decoder will display a green dot when

mains power is restored. Press On/Off symbol to

restore signal.

Tuning your TV

If your TV is not tuned to the decoder viewing channel, you will not be

able to view the satellite services. Your VCR, decoder and TV can

also interfere with each other unless they are tuned in correctly. The

output of the decoder can be tuned over the whole UHF band using

the following recommended method (refer to the following figures):

1 Connect the satellite dish and terrestrial antenna (installer).

2 Connect the installation as shown (if VCR installed).

3 Switch on the TV and select an unused channel to use with

your VCR.

4 Switch on your VCR, then set its test signal to ON (see VCR

instruction manual).

5 Tune the TV to the test signal from the VCR. Switch off the

VCR test signal.

Inf

Sca n n i ng

Waiti n g for N IT acqui siti o n

Press EXIT to cancel scanning

dL with yellow dot indicates

software being down-loaded

Number 1 with rotating bar and

yellow dot. Indicates decoding

process is in progress

Display flashes briefly

Three flashing bars and red dot

Inf (information) appears

at the same time as

scanning screen on TV

Number of last used

service appears

1 2 3 4 5 6 7 8 9 10 11 ... 37 38

Comentarios a estos manuales

Sin comentarios

UEC DSD 700 Especificaciones Pagina 6

Comentarios a estos manuales

Relacionado con productos y manuales para Receptor UEC DSD 700